SpeedyBee F7 V3 BL32 50A 30×30 Stack FPV FC Flight Controller ESC

SpeedyBee F7 V3 BL32 50A 30×30 Stack FPV FC Flight Controller ESC

1.300kr

Availability: Out of stock SKU: 964386, Barcode: SB-STACK-F7V3-50A Categories: , ,

Email when stock available

Description

SpeedyBee F7 V3 BL32 50A 30×30 Stack FPV FC Flight Controller ESC

Whether you’re at home or at the flying field, your SpeedyBee F7 V3 is always ready for you. Configure your newly built quad wirelessly, or fine tune your PIDs, access your black box data and configure all other parameters between flights in just minutes.

Forget your laptop. With SpeedyBee F7 V3 you can configure your FC with your smartphone.

 

Technical Data Flight Controller

  • Product name SpeedyBee F7 V3 Flight Controller
  • MCU: STM32F722
  • IMU(Gyro): BMI270
  • USB connector: Type-C
  • Barometer: BMP280
  • OSD chip: AT7456E chip
  • BLE Bluetooth: Supported. Used for flight controller configuration
  • Flash FC Firmware Wirelessly: Supported. Please select MENU > FC Firmware Flasher
  • Download/Analyze Blackbox: Supported: MENU > Blackbox Analyzer
  • DJI Air Unit Connection Way: Two ways are supported: 6-pin connector or direct soldering.
  • Flash (for BlackBox): 500MB
  • BetaFlight Camera Control Pad: Yes (CC Pad on the front)
  • Power input: 3S – 6S Lipo
  • 5V Output: 10 groups of 5V outputs, three +5V pads and 1 BZ+ pad (for buzzer) on the front and 6 +5V outputs in the connectors on the bottom. The total current load is 2A.
  • 9V output: 2 groups of 9V outputs, one +9V pad on the front and another in a connector on the bottom. The total current load is 4A.
  • 3.3V output: Supported. Designed for receivers with 3.3V input. Up to 500mA current load.
  • 4.5V output: Supported. Designed for receiver and GPS module even if FC is powered by USB port. Up to 1A current load.
  • ESC signal pads: M1 – M4 on the bottom and M5-M8 on the front.
  • UART: 5 sets (UART1, UART2, UART3, UART4 (for ESC telemetry), UART6)
  • ESC telemetry UART: R4(UART4)
  • I2C: Supported. SDA & SCL pads on the front panel. Used for magnetometer, sonar, etc.
  • LED pad: Used for WS2812 LEDs controlled by Betaflight firmware.
  • Buzzer: BZ+ and BZ- pad for 5V buzzer
  • BOOT button: Supported.
  • [A]. Pressing and holding the BOOT button while powering on the FC forces the FC to enter DFU mode to flash the firmware when the FC is bricked.
  • [B]. When the FC is powered on and in standby mode, the BOOT button can be used to control the LED strips connected to the LED1-LED4 connectors on the bottom panel. By default, a short press of the BOOT button will toggle the LED display mode. A long press of the BOOT button toggles between SpeedyBee LED mode and BF LED mode. In BF-LED mode all LED1-LED4 strips are controlled by the Betaflight firmware.
  • RSSI input: is supported. Referred to as RS on the front panel.
  • SmartPort: use any TX pad of the UART for the SmartPort function.
  • Supported flight control firmware BetaFlight (default), EMUFlight, INAV
  • Firmware target name: SPEEDYBEEF7V3
  • Mounting: 30.5 x 30.5mm (4mm hole diameter)
  • Dimensions: 41(L) x 38(W) x 8.1(H)mm
  • Weight: 10.7g

 

Technical Data ESC

  • Firmware: SpeedyBee BL32 50A
  • Configurator download link: http://github.com/bitdump/BLHeli/releases
  • Continuous current: 50A * 4
  • Burst current: 55A(5S)
  • TVS protection diode: Yes
  • Heat sink: Yes
  • External capacitor: 1500uF Low ESR capacitor (in case)
  • ESC Protocol: DSHOT300/600
  • Current input: 3-6S LiPo
  • Current output: VBAT
  • Current sensor support: (scale=490 offset=0)
  • Mounting: 30.5 x 30.5mm (4mm hole diameter)
  • Dimensions: 45.6(L) * 40(W) * 8.8mm(H)
  • Weight: 19.2g with heat sink

 

Contents:

  • 1x Speedy Bee F7 V3 Flight Controller
  • 1x Speedy Bee BL32 50A 4-in-1 ESC
  • 1x DJI 6pin Cable (80mm)
  • sH1.0 mm 15mm long 8pin cable (for FC-ESC connection)
  • 5x M3*8mm Silicone Grommets for FC
  • 5x M3*8mm Silicone Grommets for ESC
  • 5x M3*30mm hexagon socket screws
  • 5x M3 Silicone O Ring
  • 5x M3 Nylon Nut
  • 1x 35 V 1500uF Low ESR Capacitor
  • 1x XT60 power cable (70 mm)
  • 1x 4pin SH1.0 to 3+2pin JST1.25 FPV cam cable (30mm)
  • 1x 4pin SH1.0 to 3+2pin JST1.25 FPV Cam cable (60mm)
  • 1x 4pin SH1.0 to 4pin JST1.25 FPV Cam cable (60mm)
  • 1x 4pin SH1.0 radio receiver cable (100mm)
  • 1x 4pin SH1.0 to 4pin SH1.0 Analog VTX Cable – Yellow and blue wires are connected (60mm)
  • 1x 6pin SH1.0 GPS module cable without connector at the other end (100mm)
  • 1x 6pin SH1.0 GPS module cable with connector on other end

Additional information

Weight114 g
Brand

speedybee

Reviews

There are no reviews yet.


Only logged in customers who have purchased this product may leave a review.